CCNP Data Center 350-601 DCCOR Exam Dumps have been Updated

1. An engineer must configure a VXLAN routing on a cisco Nexus 9000 series Switch. The engineer requires a solution where all the leaf switches have the same gateway MAC and IP address .

Which configuration set accomplishes this task?

A)





B)





C)





D)

2. A customer data center is configured for distribution of user roles, call home, and NTP. The data center was split into two geographically separate locations called DC1 and DC2. The requirement is for the user role configurations to be distributed in DC1 and for NTP and call home features to be constrained to DC2 .

Which two configuration sets must be used to meet these requirements? (Choose two.)

3. Refer to the exhibit.





Why does the python code for Cisco NX-API print error message?

4. A Cisco UCS C-Series server is installed at a data center. The server should be managed by the Cisco UCS Manager by using a single cable for management and data traffic .

Which configuration should be applied after the Physical connection is established?

5. An engineer must configure OSPF in the data center. The external routes have already been redistributed OSPF.

The network must meet these criteria:

* The data centre servers must reach services in the cloud and the services behind the redistributed routes.

* The exit point toward the internet should be propagated only when there is a dynamically learned default route from the upstream router.

Which feature is required?

6. Which adjacency server configuration makes two OTV edge devices located in the same site bring up the dual-site adjacency?

A)





B)





C)





D)

7. A Cisco MDS 9000 Series Switch is configured for SAN Analytics and SAN Telemetry Streaming. An engineer must enable analytics for NVMe on interfaces in the range of fc1/1- 12. Due to a large amount of traffic generated in the SAN environment, the data must be collected at regular intervals of 60 seconds from ports fc 1-12 and then for ports fc13-24 for the next 60 seconds. Ports in the range fc4/13-14 were already enabled for analytics .

Which set of commands must be used to meet these requirements?

8. A customer wants to offload some of its order processing to a public cloud environment. The customer environment is based on Cisco ACI and uses Puppet with containenzed applications. The operations team requires a solution to orchestrate and optimize the cost of the new solution .

Which product must be used to meet these requirements?

9. DRAG DROP

Refer to the exhibit.





Drag and drop each traffic flow type from the left onto the corresponding number on the right Not all traffic flow types are used

10. Refer to the exhibit.





Which type of backup is required to restore a Cisco UCS configuration?

11. An engineer is enabling port security on a Cisco MDS 9000 Series Switch .

Which feature of enabling port security on a Cisco MDS 9000 Series Switch must be considered?

12. A network architect considers a Cisco HyperFlex design solution for a company. The proposed solution is for a virtual environment that is not performance-sensitive, but the solution must have high storage capacity and a low cost .

Which Cisco HyperFlex storage configuration should be used?

13. Refer to the exhibit .





Which configuration ensure that the cisco Nexus 7000 series switches are the primary devices for LACP?

A)





B)





C)





D)

14. A new employee must be granted access to add VLANs into an existing Cisco UCS Manager and configure NTP synchronization with date and time zone settings .

Which two privileges must be granted to the employee to complete the task? (Choose two.)

15. Which feature must be enabled to support the use of JSON and XML encoding when a Cisco Nexus 7000 series switch is deployed?

16. CORRECT TEXT

Which server policy is used to install new Cisco IMC software on a server?

17. DRAG DROP

An engineer is implementing NetFlow on a Cisco Nexus 7000 Series Switch.

Drag and drop the NetFlow commands from the left into the correct order they must be entered on the right.

18. A customer has a requirement for an automation solution that supports periodically acquiring configuration from a centralized server and aligning UCS servers to their desired state .

Which open-source tool meets these requirements?

19. A Cisco UCS user called "Employee1" accidentally changed the boot policy of the Cisco UCS server at the Cisco UCS Manager root level. This change impacted all service profiles and their storage connectivity was lost. The system administrator wants to prevent this issue from recurring in the future. The new security policy mandates that access must be restricted up to the organization level and prevent other users from modifying root policies .

Which action must be taken to meet these requirements?

20. An engineer is using REST API calls to configure the cisco APIC .

Which data structure must be used within a post message to receive a login token?

21. Several production and development database servers exist in the same EPG and IP subnet. The IT security policy is to prevent connections between production and development .

Which attribute must be used to assign the servers to different microsegments?

22. Refer to the exhibit.





An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3 .

Which configuration must be implemented to accomplish this goal?

A)





B)





C)





D)

23. Refer to the exhibit.





A host with source address 10.10.10.10. sends traffic to multicast group 239.1.1.1.

How do the vPC switches forward the multicast traffic?

24. What is a characteristic of the install all command on the cisco Nexus series switch?

25. An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional, the router must be the active master .

Which set of commands must be used to implement the scenario?

26. An engineer must start a software upgrade on a Cisco Nexus 5000 Series Switch during a zone merge .

What is the result of this action?

27. A customer needs a tool to take advantage of the CI/CD model to streamline its operation and optimize cost. The customer wants to integrate the solution with the cisco products it currently it currently uses, Including Cisco ACI networking and Cisco UCS servers. The solution should also provide on-premises Kubernetes and AppDynamics performance monitoring. Because of the security requirements, the solution not install a local client on products under management.

Which orchestration solution meets these requirements?

28. An engineer must build a lab replica of a Cisco UCS production environment. The file must be imported into a new Cisco UCS cluster using a Cisco UCS manager GUI. The file must be in XML format and be exported from Cisco UCS Manager using encrypted method.

Which two configuration parameters should be selected to meet these requirements? (Choose two.)

29. The Cisco Nexus 5600 Series Switch experiences occasional packet drops on interface ethernet 1/16. An engineer wants to implement a SPAN session to investigate the issue further. The network analyzer to which the packets must be directed is located on interface 1/3. The analyzer is limited on disk space available for traffic capture, so the Nexus switch should send only the relevant data .

Which two command sets configure the SPAN session that meets these requirements? (Choose two.)

30. The Cisco Nexus switch Generic Online Diagnostics policy for a PortLoopback test requires 10 consecutive failures to error disable the port. The customer wants to change it to 5 consecutive failures .

Which configuration applies the changes for module 1 only?

31. An environment consists of a Cisco MDS 9000 Series Switch that uses port channels. An engineer must ensure that frames between the source and the destination follow the same links for a specific flow. Subsequent flows are allowed to use a different link.

Which load balancing method should be used to accomplish this goal?

32. A network engineer must configure a power redundancy policy on a Cisco UCS C-Series Rack Server. The power redundancy must support two power sources being used to power the server .

Which configuration should be applied to meet the requirement?

33. An engineer configures an intersignt virtual application and must claim over 200 targets. The engineer starts the Claim target procedure.

The engineer has prepared this initial comma- separated value file to provision the targets:





Which Information must be included In the comma-separated value flit to provision the targets?

34. What is a feature of NFS?

35. Refer to the exhibit.





What is the outcome of this command when the ELPD is updated on a Cisco Nexus 9000 series switch?

36. Port security is statically configured on a Cisco Nexus 7700 Series switch and F3 line card. The switch is configured with an Advanced Services license .

Which two actions delete secured MAC addresses from the interface? (Choose Two)

37. Due to a major version change, an engineer must perform a software upgrade on a Cisco Nexus Series switch .

Which two technologies can be implemented to reduce disruptions to the network during the upgrade? (Choose two.)

38. Which storage protocol reduces file locks by using leasing?

39. Refer to the exhibit.





An engineer configures FCIP on a Cisco MDS 9000 Series switch .

What is the result of implementing the configuration?

40. DRAG DROP

Refer to the exhibit.





In a bidirectional PIM network using Phantom RP as an RP redundancy mechanism, two

Cisco NX-OS routers have these requirements:

• R1 must be the active RP.

• R2 must be the backup RP that is used only if R1 is not reachable

Drag and drop the configuration steps to complete the configuration for Router 2. Not all configuration steps are used.

41. Refer to the exhibit.





Which two Cisco UCS components are upgraded as a result of the configuration? (Choose two.)

42. An engineer is implementing Cisco Intersight in a secure environment. The environment must use LDAP directory service and ensure information integrity and confidentiality .

Which two steps must be taken to implement the solution? (Choose two.)

43. An engineer implements an ACI fabric and must implement microsegmentation of endpoints within the same IP subnet using a network-based attribute. The attribute mapping must allow IP subnet independence .

Which attribute must be selected?

44. Host 1 is in VLAN 100 located is DataCenter 1 and Host2 is in VLAN200 located in DataCenter2 .

Which OTV VLAN mapping configuration allows Layer 2 connectivity between these two hosts?

A)





B)





C)





D)

45. An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth 1/2 interface for both switches must be advertised via OSPF. However, these interfaces must not establish OSPF adjacency or send routing updates. The current OSPF adjacency over the interface Eth1/1 on SW1 and Eth1/1 on SW2 must remain unaffected .

Which configuration must be applied to both Nexus switches to meet these requirements?

46. A network administrator must configure an extra keyring in Cisco UCS Manager. The key must provide a high level of encryption and secure authentication when users use the web interface .

Which configuration command set must be applied to meet these requirements?

47. DRAG DROP

A network engineer must implement RBAC on Cisco MDS 9000 Series Multilayer Switches.

Drag and drop the Cisco MDS 9000 Series roles from the left onto the correct categories on the right.

48. An engineer is configuring a backup operation on the existing Cisco UCS environment using a logical configuration .

Which configuration is expected to be saved by using this backup type?

49. Refer to the exhibit.





Which command is run from the Guest Shell to set the description on the first five interfaces of the Cisco Nexus switch?

50. Which data structure results from running this Python code?

51. A network architect must redesign a data center on OSPFv2. The network must perform fast reconvergence between directly connected switches .

Which two actions must be taken to meet the requirement? (Choose two)

52. A network engineer is adding a Cisco HyperFlex data platform to the Cisco intersight management portal .

Which two components are required for Intersight to claim the Cisco HyperFlex data platform? (Choose two.)

53. What is a characteristic of EPLD updates on Cisco MDS 9000 Series Switches?

54. DRAG DROP

A storage engineer must configure zoning on a Cisco MDS 9000 Series switch.

Drag and drop actions from the left into the order on right

55. An engineer is enabling port security on a Cisco MDS 9000 Series Switch .

Which feature of enabling port security on a Cisco MDS 9000 Series Switch must be considered?

56. A network architect considers a Cisco HyperFlex design solution for a company. The proposed solution is for a virtual environment that is not performance-sensitive, but the solution must have high storage capacity and a low cost .

Which Cisco HyperFlex storage configuration should be used?

57. Refer to the exhibit .





Which configuration ensure that the cisco Nexus 7000 series switches are the primary devices for LACP?

A)





B)





C)





D)

58. A new employee must be granted access to add VLANs into an existing Cisco UCS Manager and configure NTP synchronization with date and time zone settings .

Which two privileges must be granted to the employee to complete the task? (Choose two.)

59. Which feature must be enabled to support the use of JSON and XML encoding when a Cisco Nexus 7000 series switch is deployed?

60. CORRECT TEXT

Which server policy is used to install new Cisco IMC software on a server?

61. DRAG DROP

An engineer is implementing NetFlow on a Cisco Nexus 7000 Series Switch.

Drag and drop the NetFlow commands from the left into the correct order they must be entered on the right.

62. A customer has a requirement for an automation solution that supports periodically acquiring configuration from a centralized server and aligning UCS servers to their desired state .

Which open-source tool meets these requirements?

63. A Cisco UCS user called "Employee1" accidentally changed the boot policy of the Cisco UCS server at the Cisco UCS Manager root level. This change impacted all service profiles and their storage connectivity was lost. The system administrator wants to prevent this issue from recurring in the future. The new security policy mandates that access must be restricted up to the organization level and prevent other users from modifying root policies .

Which action must be taken to meet these requirements?

64. An engineer is using REST API calls to configure the cisco APIC .

Which data structure must be used within a post message to receive a login token?

65. Several production and development database servers exist in the same EPG and IP subnet. The IT security policy is to prevent connections between production and development .

Which attribute must be used to assign the servers to different microsegments?

66. Refer to the exhibit.





An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3 .

Which configuration must be implemented to accomplish this goal?

A)





B)





C)





D)

67. Refer to the exhibit.





A host with source address 10.10.10.10. sends traffic to multicast group 239.1.1.1.

How do the vPC switches forward the multicast traffic?

68. What is a characteristic of the install all command on the cisco Nexus series switch?

69. An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional, the router must be the active master .

Which set of commands must be used to implement the scenario?

70. An engineer must start a software upgrade on a Cisco Nexus 5000 Series Switch during a zone merge .

What is the result of this action?

71. A customer needs a tool to take advantage of the CI/CD model to streamline its operation and optimize cost. The customer wants to integrate the solution with the cisco products it currently it currently uses, Including Cisco ACI networking and Cisco UCS servers. The solution should also provide on-premises Kubernetes and AppDynamics performance monitoring. Because of the security requirements, the solution not install a local client on products under management.

Which orchestration solution meets these requirements?

72. An engineer must build a lab replica of a Cisco UCS production environment. The file must be imported into a new Cisco UCS cluster using a Cisco UCS manager GUI. The file must be in XML format and be exported from Cisco UCS Manager using encrypted method.

Which two configuration parameters should be selected to meet these requirements? (Choose two.)

73. The Cisco Nexus 5600 Series Switch experiences occasional packet drops on interface ethernet 1/16. An engineer wants to implement a SPAN session to investigate the issue further. The network analyzer to which the packets must be directed is located on interface 1/3. The analyzer is limited on disk space available for traffic capture, so the Nexus switch should send only the relevant data .

Which two command sets configure the SPAN session that meets these requirements? (Choose two.)

74. The Cisco Nexus switch Generic Online Diagnostics policy for a PortLoopback test requires 10 consecutive failures to error disable the port. The customer wants to change it to 5 consecutive failures .

Which configuration applies the changes for module 1 only?

75. An environment consists of a Cisco MDS 9000 Series Switch that uses port channels. An engineer must ensure that frames between the source and the destination follow the same links for a specific flow. Subsequent flows are allowed to use a different link.

Which load balancing method should be used to accomplish this goal?

76. A network engineer must configure a power redundancy policy on a Cisco UCS C-Series Rack Server. The power redundancy must support two power sources being used to power the server .

Which configuration should be applied to meet the requirement?

77. An engineer configures an intersignt virtual application and must claim over 200 targets. The engineer starts the Claim target procedure.

The engineer has prepared this initial comma- separated value file to provision the targets:





Which Information must be included In the comma-separated value flit to provision the targets?

78. What is a feature of NFS?

79. Refer to the exhibit.





What is the outcome of this command when the ELPD is updated on a Cisco Nexus 9000 series switch?

80. Port security is statically configured on a Cisco Nexus 7700 Series switch and F3 line card. The switch is configured with an Advanced Services license .

Which two actions delete secured MAC addresses from the interface? (Choose Two)

81. Due to a major version change, an engineer must perform a software upgrade on a Cisco Nexus Series switch .

Which two technologies can be implemented to reduce disruptions to the network during the upgrade? (Choose two.)

82. Which storage protocol reduces file locks by using leasing?

83. Refer to the exhibit.





An engineer configures FCIP on a Cisco MDS 9000 Series switch .

What is the result of implementing the configuration?

84. DRAG DROP

Refer to the exhibit.





In a bidirectional PIM network using Phantom RP as an RP redundancy mechanism, two

Cisco NX-OS routers have these requirements:

• R1 must be the active RP.

• R2 must be the backup RP that is used only if R1 is not reachable

Drag and drop the configuration steps to complete the configuration for Router 2. Not all configuration steps are used.

85. Refer to the exhibit.





Which two Cisco UCS components are upgraded as a result of the configuration? (Choose two.)

86. An engineer is implementing Cisco Intersight in a secure environment. The environment must use LDAP directory service and ensure information integrity and confidentiality .

Which two steps must be taken to implement the solution? (Choose two.)

87. An engineer implements an ACI fabric and must implement microsegmentation of endpoints within the same IP subnet using a network-based attribute. The attribute mapping must allow IP subnet independence .

Which attribute must be selected?

88. Host 1 is in VLAN 100 located is DataCenter 1 and Host2 is in VLAN200 located in DataCenter2 .

Which OTV VLAN mapping configuration allows Layer 2 connectivity between these two hosts?

A)





B)





C)





D)

89. An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth 1/2 interface for both switches must be advertised via OSPF. However, these interfaces must not establish OSPF adjacency or send routing updates. The current OSPF adjacency over the interface Eth1/1 on SW1 and Eth1/1 on SW2 must remain unaffected .

Which configuration must be applied to both Nexus switches to meet these requirements?

90. A network administrator must configure an extra keyring in Cisco UCS Manager. The key must provide a high level of encryption and secure authentication when users use the web interface .

Which configuration command set must be applied to meet these requirements?

91. DRAG DROP

A network engineer must implement RBAC on Cisco MDS 9000 Series Multilayer Switches.

Drag and drop the Cisco MDS 9000 Series roles from the left onto the correct categories on the right.

92. An engineer is configuring a backup operation on the existing Cisco UCS environment using a logical configuration .

Which configuration is expected to be saved by using this backup type?

93. Refer to the exhibit.





Which command is run from the Guest Shell to set the description on the first five interfaces of the Cisco Nexus switch?

94. Which data structure results from running this Python code?

95. A network architect must redesign a data center on OSPFv2. The network must perform fast reconvergence between directly connected switches .

Which two actions must be taken to meet the requirement? (Choose two)

96. A network engineer is adding a Cisco HyperFlex data platform to the Cisco intersight management portal .

Which two components are required for Intersight to claim the Cisco HyperFlex data platform? (Choose two.)

97. What is a characteristic of EPLD updates on Cisco MDS 9000 Series Switches?

98. DRAG DROP

A storage engineer must configure zoning on a Cisco MDS 9000 Series switch.

Drag and drop actions from the left into the order on right

99. Refer to the exhibit.





An engineer must configure FCoE on a Cisco Nexus switch .

Which two command sets complete this configuration? (Choose two.)

100. What is required for using puppet in a Cisco NX-OS environment?

101. Which two configuration settings are available in the in the cisco UCS flmware Auto sync server policy?

102. An engineer must use the Embedded Event Manager to monitor events that occur on a cisco Nexus 9000 series switch. An environment variable needs to be created so that several policies use the monitored events in in their actions. The external email server is represented by IP address 10.10.10.10.

Which command sets the environment variable?

103. An engineer is implementing OTV on a transport that supports multicast.

The solution needs to meet the following requirements:

• Establish adjacency to the remote peer by using multicast.

• Enable OTV advertisements for VLAN 100 to the other site.

Which two commands should be configured to meet these requirements? (Choose two.)

104. A network engineer must create an EEM script that saves a copy of the running configuration on bootflash and writes a message to syslog when a user saves the configuration to a Cisco Nexus switch .

Which configuration set should be applied to complete this task?

105. An engineer needs to monitor ingress traffic that arrives at interface Ethernet 1/3 that belongs to a Cisco Nexus 5600 Series Switch. The traffic analyzer machine located at interface Ethernet 1/5 is already monitoring other production, and the traffic analyzer must not be impacted by the traffic captured from the interface Eth1/3. The operations team allocated a traffic budget for the new monitoring session of 1 Gbps to meet this requirement.

Which set of commands configures the SPAN session?

106. Refer to the exhibit.





Esxi-server is associated to the blade server. A VLAN added to trunk-a. the VLAN is missing on the vNIC of ESXI-server .

Which action should be taken to add the VLAN to the cNIC?

107. An engineer must configure HTTPS secure management for Cisco UCS Manager using a key ring named kr2016 and a key size of 1024 bits. The environment consists of a primary fabric interconnect named UCS-A and a secondary fabric interconnect named UCS-B .

Which command sequence must be used to accomplish this goal?

108. A network engineer configures a converged network adapter (CNA) and must associate a virtual fiber Channel 7 interface to VSAN 7. The CAN connected to the interface Eth1/7, and VLAN 700 is mapped to the VSNA .

Which configuration must be applied to create the virtual Fiber Channel interface and associate it with the Ethernet physical interface?

A)





B)





C)





D)

109. Refer to the exhibit.





What is the result of implementing this configuration?

110. An engineer is implementing OTV on a transport that supports multicast. The solution needs to meet the following requirements:

• Establish adjacency to the remote peer by using multicast.

• Enable OTV advertisements for VLAN 100 to the other site.

Which two commands should be configured to meet these requirements? (Choose two.)

111. An engineer needs to monitor ingress traffic that arrives at interface Ethernet 1/3 that belongs to a Cisco Nexus 5600 Series Switch. The traffic analyzer machine located at interface Ethernet 1/5 is already monitoring other production, and the traffic analyzer must not be impacted by the traffic captured from the interface Eth1/3. The operations team allocated a traffic budget for the new monitoring session of 1 Gbps to meet this requirement.

Which set of commands configures the SPAN session?

112. Which statement about the MAC address that the FCoE Initialization Protocol chooses for use by an E-Node in an FCoE implementation is true?

113. Refer to the exhibit.





What is configured as a result of running these commands?

114. An engineer is implementing a Cisco UCS system with directly connected Fibre channel storage array.

Which two actions should be taken to accomplish this task? (Choose two.)

115. An engineer must ensure fabric redundancy when implementing NPV mode on a Cisco MDS 9000 Series Switch.

Which action enables fabric redundancy?

116. Refer to the exhibit.





The STP priority of N7K-1 and N7K-2 are the lowest in the network.

Which statement describes STP on the vPC?

117. Which Cisco network assurance engine feature helps reduce the need for Tier 1 network operation centers to escalate issues?

118. An engineer must generate a checkpoint of the running configuration on a Cisco Nexus Switch. The checkpoint file name must be called "before_maintenance' and should be used for recovering the switch to its pre-maintenance state. The rollback of the checkpoint to running configuration should only occur if no errors occur.

Which two configuration commands must be used to meet these requirements? (Choose two.)

119. A DNS server with IP address 192.168.1.1 is deployed in a data center A network engineer must configure a Cisco UCS Fabric Interconnect to use this DNS.

Which configuration should be applied?

120. Which two statements about the process of performing an EPLD upgrade on a Cisco MDS

9000 series Switch are true? (Choose two.)

121. Refer to the exhibit.





What is the result of implementing this configuration?

122. Multiple roles are applied to a user on the Cisco MDS 9000 Series Switch.

Which statement is true?

123. Which adjacency server configuration makes two OTV edge devices located in the same site bring up the dual-site adjacency?

A)





B)





C)





D)

124. An engineer implements SPAN configuration on an Nexus 5000 series switch.





Which two commands are necessary to complete the SPAN session configuration? (Choose two)

125. An engineer is configuring AAA authentication on an MDS 9000 switch. The LDAP server is located under the IP 10.10.2.2. The data sent to the LDAP server should be encrypted.

Which command should be used to meet these requirements?

126. An engineer creates a service profile in Cisco UCS Manager and must assign a policy that reboots blades when changes are applied. The changes must be applied only after user acknowledgment.

Which two policies must be configured to meet these requirements? (Choose two.)

127. Which statement describes monitoring Fibre Channel traffic on a Cisco UCS 6332 Fabric Interconnect?

128. Refer to the exhibit.





What is the result of this series of commands?

129. What are two capabilities of the Cisco Network Assurance Engine? (Choose two.)

130. Which configuration implements static ingress replication?

131. What occurs when running the command install deactivate <filename> while a software maintenance upgrade is performed on a Cisco Nexus 9000 Series switch?

132. DRAG DROP

An engineer must upgrade a Cisco Nexus 9500 Series Switch. The requirement is for all switch components to be upgraded in batches.

Drag and drop the components from the left into the order in which they should be upgraded, on the right, for the upgrade process to complete successfully Not all components are used.

133. An engineer needs to create a new user in the local user database on Cisco UCS Fabric Interconnect.

The user needs permissions to change the following configuration inside UCS Manager version 3.1:

• vNIC and vHBA profiles

• Fan speed and power redundancy profile of UCS Manager

Which two roles must be assigned to a user to achieve this goal? (Choose two.)

134. DRAG DROP

Drag and drop the mechanisms to collect data from a network from the left onto their characteristics on the right

135. What is an advantage of NAS compared to SAN?

136. A network engineer an EPLD update on the fan modules of a Cisco Nexus 7000 series switch.









What is the impact if “y is selected to continue?

137. Which two actions should be taken before an upgrade is started on a Cisco MDS switch? (Choose two.)

138. What is a benefit of using the Cisco UCS Lightweight upgrade feature?

139. A server engineer wants to control power uses on a Cisco UCS C-series rack server down to the component level.

Which two components support specific power limits? (Choose two.)

140. A network architect considers a Cisco HyperFlex design solution for a company. The proposed solution is for a virtual environment that is not performance-sensitive, but the solution must have high storage capacity and a low cost.

Which Cisco HyperFlex storage configuration should be used?

141. Refer to the exhibit.





What be connected to clear the HA NOT READY status?

142. A POAP-enabled Cisco Nexus switch will not enter POAP mode.

Which two conditions should be verified? (Choose two.)

143. AN engineer is asked to modify an overridden policy by changing the number of FCNS database entries to 1500 and then generable a massage.

What configuration will accomplish this task?

A)





B)





C)





D)

144. An engineer created a service profile in Cisco UCS Manager and associated it to a server. The engineer must create a policy if there is a disruptive change applied to the service profile.

Which policy type must be used to accomplish this goal?

145. An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional the router must be the active master.

Which set of commands must be used to implement the scenario?

146. Which MAC address is an HSRP version 2?

147. Refer to the exhibit.





What is the outcome of this command when the ELPD is updated on a Cisco Nexus 9000 series switch?

148. A network engineer must create a Python application to replace the process of manual Cisco ACI configuration. The engineer requires a tool to assist the engineer with the development process that must support a graphical user interface and allow a user to browse the Cisco ACI object model. For security reasons, the tool must prevent a user from making configuration changes to the target system.

Which two tools must be used to meet these requirements? (Choose two.)

149. An engineer must create a backup file of the entire Cisco UCS system before the maintenance window starts. The backup file must include these attributes:

• all logical configuration settings such as service profiles. VLANs. and VSANs

• all Cisco UCS usernames. roles, and locales

• all Cisco UCS system settings

Which backup type must be selected to achieve this goal?

150. AN engineer enters these commands while in EEM on a Cisco Nexus 9000 Series Switch.

event manager applet Backup-config

event timer watchdog time 1800 name timer

event cli match “copy running-config startup-config”

what is the result of applying this configuration?

151. What happens to the default host firmware policy after a Cisco UCS Manager upgrade?

152. A customer has a requirement for an automation solution that supports periodically acquiring configuration from a centralized server and aligning UCS servers to their desired state.

Which open-source tool meets these requirements?

153. Which two hypervisors does Cisco HyperFlex support? (Choose two.)

154. An engineer needs to implement a solution that will provide telemetry of MDS 9000 switches in a SAN fabric. The solution should use Cisco Data Center Network Manager (DCNIM) with SAN insights feature.

Which three steps are required to deploy the solution? (Choose Three.)

155. Refer to the exhibit.





Cisco Fabric Services is enabled in the network.

Which type of IP address is used by the Cisco Fabric Services protocol?

156. An engineer requires a solution to automate the configuration and deployment of remote network devices for a customer.

The engineer must keep these considerations in mind:

• The customer's environment is based on industry-accepted standards and requires a solution that meets these standards.

• The security requirements mandate the use of a secure transport mechanism between the automation software and target devices such as SSH or TLS.

• The solution must be based on a human-readable and easy to parse format such as XML or JSON.

Which solution must be used to meet these requirements?

157. An engineer is implementing NPV mode on a Cisco MDS 9000 Series Switch.

Which action must be taken?

158. DRAG DROP

Drag and drop the storage technologies from the left onto the correct descriptions on the right.

159. Host 1 is in VLAN 100 located is DataCenter 1 and Host2 is in VLAN200 located in DataCenter2.

Which OTV VLAN mapping configuration allows Layer 2 connectivity between these two hosts?

A)





B)





C)





D)

160. Which mroute state is created when Bidirectional PIM is deployed at a site?

161. What is a feature of NFS?

162. Which feature must be enabled to support the use of JSON and XML encoding when a Cisco Nexus 7000 series switch is deployed?

163. Which two settings must be configured before enabling a Cisco UCS Manager domain for Cisco Intersight connectivity? (Choose two.)

164. Which server policy is used to install new Cisco IMC software on a server?

165. A host EDG Client wants to talk to a webserver in EGP Web. A contract with default settings is defined between EPG Client and EPG Web, which allows TCP communication initiated by the client toward the webserver with TCP destination port 80.

Which statement is true?

166. Which two components should be checked when a Cisco Nexus 9000 Series Switch fails to boot using POAP? (Choose two.)

167. Refer to the exhibit.





Which type of backup is required to restore a Cisco UCS configuration?

168. Which product includes prebuilt templates that can be used to customize fabric deployments?

169. What is a characteristic of electronic programmable logic device (EPLD) software upgrades?

170. An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before importing it to a target fabric interconnect.

Which backup type must be selected to meet these requirements?

171. DRAG DROP

An engineer is implementing NetFlow on a Cisco Nexus 7000 Series Switch.

Drag and drop the NetFlow commands from the left into the correct order they must be entered on the right.

172. An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image.

What is expected to occur in this case?

173. Refer to the exhibit.





Why does the python code for Cisco NX-API print error message?

174. DRAG DROP

Drag and drop the characteristics from the left onto the correct storage systems on the right.

175. Which method must a network engineer use to upgrade the BIOS firmware of a Cisco UCS standalone C-Series reck-mount server?

176. An engineer needs a utility to translate traditional Nexus CLI inputs and generate Python code using XML and JSON message formats. The solution needs to be available on a Nexus 7700 series switch.

Which utility should be used?

177. An engineer is configuring a backup operation on the existing Cisco UCS environment using a logical configuration.

Which configuration is expected to be saved by using this backup type?

178. A Cisco UCS C-Series server is installed at a data center. The server should be managed by the Cisco UCS Manager by using a single cable for management and data traffic.

Which configuration should be applied after the Physical connection is established?

179. Which three firmware packages are included in the Cisco UCS C-Series Rack-Mount UCS-Managed Server Software bundle? (Choose three.)

180. A network architect is asked to design and manage geographically distributed data centers across cities and decides to use a Multi-Site Orchestrator deployment.

How many orchestrators should be deployed?

181. Refer to the exhibit.





Which two Cisco UCS components are upgraded as a result of the configuration? (Choose two.)

182. Refer to the exhibit.





Which command is run from the Guest Shell to set the description on the first five interfaces of the Cisco Nexus switch?

183. Refer to the exhibit.





Which command needs to be added to the line starling with the "file" keyword to have the generated running-config file with the name 'fusion-config_' and current date?

184. An engineer must configure RBAC is Cisco UCS Manager in an existing data center environment.

Which two roles can be used to configure LAN Connectivity policies? (Choose two.)

185. An engineer needs to install a new package on a Cisco Nexus 9000 Series Switch.

What is the impact of running the install commit <filename> command on the switch?

186. Refer to the exhibit.





What is the reason the system-fm-vrrp checkpoint was created?

187. An engineer needs to Implement a solution that prevents loops from occurring accidentally by connecting a switch to interface Ethemet1/1. The port Is designated to be used tor host connectivity.

What configuration should be implemented?

188. DRAG DROP

Refer to the exhibit.





Drag and drop each traffic flow type from the left onto the corresponding number on the right Not all traffic flow types are used

189. Where is the witness deployed in a two-node Cisco HyperFlex Edge deployment?

190. Due to a major version change, an engineer must perform a software upgrade on a Cisco Nexus Series switch.

Which two technologies can be implemented to reduce disruptions to the network during the upgrade? (Choose two.)

191. An engineer configures a storage environment for a customer with high-security standards. The secure environment is configured in vsan 50. The customer wants to maintain a configuration and active databases and prevent unauthorized switches from joining the fabric. Additionally, the switches must prevent rogue devices from connecting to their ports by automatically learning the WWPNs of the ports connected to them for the first time.

Which two configuration sets must be used to meet these requirements? (Chose two.)

192. DRAG DROP

Drag and drop the steps on the left onto the order that they must be implemented on the right to recover a fabric interconnect when there is no working image on the bootflash.

193. Refer to the exhibit.





Which setting must be configured to prevent reuse of passwords?

194. Which virtual MAC address is the default for HSRP version 2 group 10?

195. Which two components are used by the Cisco Nexus switches telemetry process? (Choose two)

196. Refer to the exhibit.





What is a characteristic of the UUID in the service profile presented?

197. The FCoE technology is used in a data center and the MDS switches are configured as Fibre Channel Forwarders.

What configuration should be applied to an MDS switch in order to be used as the best switch to connect by the CNAs in the fabric?

198. An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional the router must be the active master.

Which set of commands must be used to implement the scenario?

199. A network engineer repeatedly saves a configuration on Catalyst switches to NVRAM using the write memory command.

What action should be taken to implement the same action on Nexus switches?

200. An engineer is running an ACI fabric, has VMM integration with VMware vCenter, and wants to enable microsegmentation based on vCenter VM attributes.

Which statement about microsegmentation is true?

201. DRAG DROP

Drag and drop the storage technologies from the left onto the correct descriptions on the right.

202. Which action must be performed before renumbering a Cisco UCS chassis?

203. Refer to the exhibit.





Which backup operation type does not include the Preserve Identities feature?

204. Refer to the exhibit.





Which VLANs are capable to be assigned on vPC interfaces?

205. Refer to the exhibit.





Which type of backup is required to restore a Cisco UCS configuration?

206. Refer to the exhibit.





A network engineer is setting up a multihomed OTV network. The first site has been set up with a primary and secondary adjacency server.

Which configuration must be added on the remote OTV AEDs site?

207. Which command reduces the amount of time it takes to complete the ISSU on a Cisco Nexus 7000 series switch that has dual supervisor modules and two I/O modules?

208. DRAG DROP

A storage engineer must configure zoning on a Cisco MDS 9000 Series switch. Drag and drop actions from the left into the order on right

209. DRAG DROP

An engineer is implementing NetFlow on a Cisco Nexus 7000 Series Switch.

Drag and drop the NetFlow commands from the left into the correct order they must be entered on the right.

210. An engineer implements SPAN configuration on an Nexus 5000 series switch.





Which two commands are necessary to complete the SPAN session configuration? (Choose two)

211. Refer to the exhibit.





Which two Cisco UCS components are upgraded as a result of the configuration? (Choose two.)

212. Refer to the exhibit.





What be connected to clear the HA NOT READY status?

213. What is the benefit of adding Cisco HyperFlex Hardware Acceleration Cards to a HyperFlex deployment?

214. DRAG DROP

Refer to the exhibit.





In a bidirectional PIM network using Phantom RP as an RP redundancy mechanism, two Cisco NX-OS routers have these requirements:

- R1 must be the active RP.

- R2 must be the backup RP that is used only if R1 is not reachable

Drag and drop the configuration steps to complete the configuration for Router 2. Not all configuration steps are used.

215. An engineer has a primary fabric that is named UCS-A and a secondary fabric that is named UCS-B. A certificate request that has a subject name of sjc2016 for a keyring that is named kr2016 needs to be created. The cluster IP address is 10.68.68.68.

Which command set creates this certificate request?

216. An engineer wants to create a backup of Cisco UCS Manager for disaster recovery purposes.

What are two characteristics of a full state backup of a Cisco UCS Manager database? (Choose two.)

217. Refer to the exhibit.





An engineer is implementing zoning on two Cisco MDS switches. After the implementation is finished, E Ports that connect the two Cisco MDS switches becomes isolated.

What is wrong with the implementation?

218. An engineer is enabling port security on a Cisco MDS 9000 Series Switch.

Which feature of enabling port security on a Cisco MDS 9000 Series Switch must be considered?

219. What happens to the default host firmware policy after a Cisco UCS Manager upgrade?

220. Refer to the exhibit.





Which result of running the command is true?

221. Which service profile is affected if the default host firmware policy in Cisco UCS Manager is changed?

222. An engineer is implementing FCoE.

Which aspect of DCBXP on a Cisco Nexus switch affects this implementation?

223. Which event is expected during direct upgrade of Cisco UCS Manager firmware?

224. What is an advantage of steaming telemetry over SNMP?

225. DRAG DROP

Drag and drop the NAS features from the left onto the NAS descriptions on the right. Not all features are used

226. An engineer needs a utility to translate traditional Nexus CLI inputs and generate Python code using XML and JSON message formats. The solution needs to be available on a Nexus 7700 series switch.

Which utility should be used?

227. Port security is statically configured on a Cisco Nexus 7700 Series switch and F3 line card. The switch is configured with an Advanced Services license.

Which two actions delete secured MAC addresses from the interface? (Choose Two)

228. An engineer needs to install a new package on a Cisco Nexus 9000 Series Switch.

What is the impact of running the install commit <filename> command on the switch?

229. An engineer needs to create a new user in the local user database on Cisco UCS Fabric Interconnect. The user needs permissions to change the following configuration inside UCS Manager version 3.1:

vNIC and vHBA profiles

Fan speed and power redundancy profile of UCS Manager

Which two roles must be assigned to a user to achieve this goal? (Choose two.)

230. What is a recommended design choice in a topology for multipathing iSCSI traffic?

231. An engineer installed a new Nexus switch with the mgm0interface in vrf management. Connectivity to the rest of the network needs to be tested from the guest shell of the NX­OS.

Which command tests connectivity from the shell of the NX-OS?

232. Multiple roles are applied to a user on the Cisco MDS 9000 Series Switch.

Which statement is true?

233. Which two actions should be taken before an upgrade is started on a Cisco MDS switch? (Choose two.)

234. A host EDG Client wants to talk to a webserver in EGP Web. A contract with default settings is defined between EPG Client and EPG Web, which allows TCP communication initiated by the client toward the webserver with TCP destination port 80.

Which statement is true?

235. An engineer is duplicating an existing Cisco UCS setup at a new site.

What are two characteristics of a logical configuration backup of a Cisco UCS Manager database? (Choose two.)

236. A customer has a requirement for an automation solution that supports periodically acquiring configuration from a centralized server and aligning UCS servers to their desired state.

Which open-source tool meets these requirements?

237. AN engineer is implementing an import operation in Cisco UCS Manager.

What is the impact of performing this operation?